Identifying Causes of Low Water Flow Limited Exclusively to Pull-Out Kitchen Faucet Spray Heads

Identifying Causes of Low Water Flow Limited Exclusively to Pull-Out Kitchen Faucet Spray Heads
Few kitchen irritations are as mysterious as a faucet that sends a powerful flow out of the spout and a feeble sputtering stream out of the pull-out spray head. The handle works, water pressure on other fixtures seems normal and pipes under the cabinet look fine. So the faint spray makes no reason. Most often, the pattern is a useful indicator, since it suggests the household water supply is fine and the restriction is somewhere along the spray route. Pull-down and pull-out faucets work on the principle of a diverter, a flexible hose, a quick-connect connection and a spray head full of screens and tiny nozzles, and any one of those can limit flow. This article describes the construction of the system, explains why a localized problem only affects the sprayer and shows how to locate the cause with simple instruments and a logical approach.
How Spray Heads on Pull-Out Faucets Get Water
A pull-out kitchen faucet has a single body inside with two alternative water paths. Hot and cold supply lines feed a cartridge that mixes the two together and delivers them toward the spout. Inside the body of the faucet, or near the spout, is a diverter, a small valve that sends water either to the aerator at the tip or into a flexible hose that travels through the faucet neck to the spray head. The hose itself is commonly constructed of braided nylon or reinforced plastic, and is attached to the body of the faucet via a quick-connect fitting. A counterweight on the hose draws the head back into its dock. Inside the spray head is an intake screen , sometimes a flow-control washer , and at the end a nozzle plate with many tiny holes . Water has to go through each of these parts therefore making a narrow point at any stage decreases output.
Why Low Flow at the Spray Head Alone Indicates a Local Restriction
If the main spout is working OK, and only the sprayer is weak, the shutoff valves, supply lines and cartridge are almost definitely working fine. A common problem like low municipal pressure, a partially closed angle stop or a plugged supply line would restrict flow everyplace even at the spigot, and would likely influence other fixtures in the house. So a limitation that is only seen in spray mode has to dwell in the portion of the part that spout flow does not see, which is the diverter outlet, the hose, the connector and the spray head. This reduces the search tremendously and saves a lot of unneeded effort on valves and pipes. Nevertheless, verify the observation in the same position of the handle in each mode and try the sprayer both docked and in your hand, as a pulled hose can act differently than a docked hose.
Mineral Scale and Clogged Nozzle Holes on Spray Face
The most common cause is the build-up of scale on the spray face. Every time the droplets evaporate, hard water leaves calcium and magnesium deposits, and the nozzle plate, which is full of tiny holes where the water stays and evaporates after each usage, is affected. Over months such apertures close up, the spray pattern gets uneven and some jets stop altogether. Many current heads have soft silicone nozzle tips, which pick up a chalky crust that can be felt as roughness with a fingertip. The other jets shoot out at weird angles and the total output seems poor because of the continual feed and the diminishing open area. Look for white or tan crust, plugged holes and sidling streams. Often a full spray is restored by soaking the head in white vinegar and wiping the nozzle tips with a gentle brush. Do not use sharp metal instruments as they can widen or damage the openings.
Debris caught in inlet screen and hose connector
Most spray heads have a small mesh screen underneath the nozzle plate to trap sand, flakes of rust, particles of pipe sealant and rubber. After plumbing repairs, a water main break or a municipal flushing event, these particles flow through the pipes and are collected at the screen. The mesh apertures are relatively fine, so a thin layer of grit noticeably cuts flow. The same dirt can also accumulate in the coupling where the hose joins the head or in a small check valve that some manufacturers put in the connector. Take the head off the hose, look at the inlet screen in bright light and rinse it from the backside to flush the dirt out the way it came in. Tapping the screen on a towel can assist dislodge the tenacious grains that rinsing alone leaves behind.
Diverter Valve Wear, Scale and Spray Mode Switching Problem
The diverter is a little plunger or flap that controls the water’s direction, and if it sticks or wears, the hose channel might only open partially. In this case the sprayer gets a smaller part of the flow and some water still runs to the spout. Typical indications are water leaking out of the aerator when the sprayer is on, a sprayer that works well only in a certain position of the lever or flow that varies as you move the hose. Scale and sediment can get in around the diverter seat and prevent it from sealing, and aging rubber parts lose their form and spring. The diverter is usually located in the faucet body on single handle models or inside the toggle button on the spray head. Access varies by brand. This is normally resolved by cleaning or replacing with an approved manufactured part.
Pull-out hoses kinked, twisted or collapsed
The pull-out hose is a long flexible tube that is subjected to constant bending, pulling and temperature change. A hose pulled back into the cabinet with a sharp bend, caught by stored items, or tangled up with the garbage disposal line may only allow a small passage for water. A counterweight in the wrong place might potentially pinch the hose, and a weight fastened too low or too high could cause the line to fold back on itself. Inner liners can blow up, delaminate, or collapse after years of hot water, a concealed fault that looks perfectly normal on the outside. Pull the head all the way out and trace the hose under the sink looking for any bends, flattened areas and cracks. Watch the weight to see that it travels smoothly . Next carefully slide it back . A damaged lining means the hose needs replacing, not repairing.
Quick Connect Fittings, Check Valves, and Flow Restrictors
The faucet body is connected to many hoses using plastic quick-connect couplings that have O-rings and in certain designs a built-in check valve to prevent backflow. A leaking O-ring will probably be worn. A check valve that is partially jammed can restrict flow without a visible trickle. Some spray heads come with a flow-limiting washer that is commonly rated at about 1.5 gallons per minute to meet water efficiency guidelines. A missing, backward or scale swelled washer makes a big difference in the output. Connections cross threaded, couplings overtightened and hose ends bent by a clamp can also reduce the route. Ensure each connection is properly seated and retaining clip is in place. When obtaining replacements, compare them attentively to the originals as slight changes in size and thread type will effect both fit and flow.
Diagnosis, Cleaning and Prevention Step by Step
Start by comparing the flow at the spout and the sprayer . Remove the spray head and put the open end of the hose into a bucket . Slowly turn the water on . If you get a strong flow out of the open hose, the limitation is in the head; if the flow is light, the restriction is in the hose, connector or diverter. Rinse the inlet screen, soak the head in vinegar for 30 minutes to an hour, then reattach the head, repeating the bucket test after each step so you know which procedure made the difference. To stop this happening again, clean the head every few months, consider a whole-house or under-sink filter if you live in a hard water area and don’t kink the hose when pushing it back. If the hose is damaged, the diverter is stuck within the faucet body, or flow is still weak after cleaning everything, call a plumber.